MOTOROLA GR500 REPEATER PDF

The Motorola GR Repeater provides the perfect solution. By making it easy to extend your two-way system to accommodate longer distances, these. Find great deals for Motorola Radius GR Repeater Station Input Voltage / vac. Shop with confidence on eBay!. Motorola gr repeater – 12 results from brands Tram, Motorola, Icom, products like Icom MICRO UHF MHZ 50W Repeater Duplexer N CONNECTOR.

Author: Vik Vut
Country: Cayman Islands
Language: English (Spanish)
Genre: Literature
Published (Last): 18 May 2007
Pages: 180
PDF File Size: 1.88 Mb
ePub File Size: 3.84 Mb
ISBN: 163-5-32052-285-6
Downloads: 30149
Price: Free* [*Free Regsitration Required]
Uploader: Dajar

Motorola Analog Base Station/Repeater: GR500/CDR500

If you can get by with 15 channels you can have one additional input function – transmit PL inhibit, for example. If you are going to put up a repeater or a point-to-point link that will have a similar duty cycledon’t use a low-end low duty cycle mobile radio from any manufacturer as the transmitter. Believe it and heed it. One last comment on channel steering: This is sometimes called a “range 3” radio and is the most common in UHF. Well, the trick that isn’t in the manual is that to re-initialize the ZR all you have to do is repeayer hold the button labeled “Connect” in while you power the unit on and keep it held until the LED labeled “Phone” starts to flash.

I’ve seen many radios with an RJ45 plug plugged into the mic jack with a 1 inch jumper wire crimped into pins 3 and Either way, it’s the bidirectional programming data lead, which is used by the RIB for programming the radio, so leave this pin taped mitorola inside the microphone.

Motorola Radius GR Repeater Station Input Voltage /vac | eBay

Please click here to contact a rental specialist. The exciter was an MC-Micro RF board with the receiver components missing, and the receiver was another RF board with the exciter components missing.

  EZ GRADER PDF

By the way, this same trick with a larger diameter o-ring works on full size PLs it’s a very common trick used on CB radios installed in the big wheel trucks. The method of grounding this pin varies with which model of microphone is used. There was also a kit to swap the two radio chassis in a GR or GR for a single R radio this allowed a GR or GR to be narrow-banded, and the two radios that were removed could be used elsewhere or sold. The crystals passed receiving inspection, were assembled into radios and shipped to customers.

This page is oriented towards the USA marketed radios, simply because it was compiled by USA residents; we described the radios we are familiar with.

This WILL happen in a long transmit situation. Find yourself a M10, M or GM Note that the T8 is less common in the prepackaged kits If you have a M10, M, M or GMs look carefully at the old crystal before you order the replacement as some used the Corrections and additional contributions are invited. Operation outside the band limits CAN result in the power control and deviation control functions in the radios going totally berserk – one of the most common results is that the transmitter goes to full uncontrolled power output – I have seen a 60 watt low band MaxTrac put out watts See the paragraph below titled “Limitations”.

There’s an instruction sheet that explains how to remove the pins in the GM article in this section.

If you try to use a standard bracket on the high power low band MaxTrac you will soon be buying the special bracket. More key info is on the radio keys page.

  ESGRIMA BIBLICO PDF

Motorola gr repeater | Compare Prices at Nextag

It shows the extraction tool, and where to insert it. Yes, it’s a little steep, but the hard work of removing the old one IS already done Contact the page maintainer above. According to the manual, the part number for the proper speaker lead assembly, including the connector that plugs into the P10 speaker connector on the logic board is T30 “speaker cable assembly”.

Gepeater here for photos: Our team is determined and capable of rendering the best services.

The six channel radios commonly have the scan button labeled as Exit, so if you want a new full feature escutcheon as I said above it is part number is L The connector leads are thick and the circuit board holes are just big enough for them. Repearer interesting but Moto’s RSS software can do things the radio can’t – so make sure you don’t have the same function i.

Then one day the driver sat on the microphone for an hour during a road trip. As shown in the table in the microphone section above, the DeskTrac has one weirdness that has caught repaeter people.

It has memory dial also called autodiallast number dial, and is back-lit. On any radio that is new to you do NOT assume that any accessory connector pin programming is present, or if it is there, is correct for your radio environment.

If anyone would care to share information on the non-USA radios gr50 be happy to add them on this page, or even create a region-specific page.